MAX693CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | Through Hole |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Frequency | 250kHz |
| Base Part Number | MAX693 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 16 |
| Max Output Current | 20mA |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 3.5mA |
| Power Dissipation | 600mW |
| Max Supply Current | 10mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.4V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 35ms Minimum |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX693CPE+ Overview
A total of 16 terminals are used to mount this power management. Packaged in a Tube-shape, IC management comes with a number of features. For your reference, this IC power includes a list of 1 functions. A series of 1 channels can be found on this supervisor. In this PMIC, you can find 16-DIP (0.300, 7.62mm) functions for your reference. As with other Battery Backup Circuit products, this IC management also offers a wide range of benefits. According to the specification, the package's peak reflow temperature is specified to be 260. In a 5V supply voltage, the power management conducts. Power management conducts at a voltage of 1. The power management is mounted by a Through Hole-axis. A IC power such as this can be classified as a Power Management Circuits power management system. 16 pins are present in total in this power management. This power management system has 16 pins. Supply voltage (Vsup) should be at least 4.5V for this power management. This IC power should be powered by no more than 5.5V volts of supply voltage (Vsup). The recommended mounting type is Through Hole. You should set the supervisor's temperature during 0°C~70°C TA . When this power management system is in operation, it produces an output voltage of Push-Pull, Push-Pull. It is estimated that the voltage supervisor's supply current is 350μA. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX693, which is the base power ics number. To be able to work, this power management requires 5V volts of power. At the most, voltage supervisor can work with a supply temperature of 10mA. As a rule of thumb, voltage supervisor will work well in most cases with a frequency of 250kHz.
MAX693CPE+ Features
Battery Backup Circuit type
Minimum supply voltage of 4.5V
350μA operating supply current
MAX693CPE+ Applications
There are a lot of Maxim Integrated MAX693CPE+ Voltage Supervisors applications.
- Military electronics
- Military communications
- Transformer load monitoring equipment
- Electronics installed in the vehicle
- Medical-specific insulation monitor
- Network equipment
- Consumer electronics
- Display equipment
- Power communication system
- Automotive permanent magnet synchronous motors
