MAX693CWE
| Parameters | |
|---|---|
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX693 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 10mA |
| Nominal Supply Current | 2mA |
| Max Supply Current | 10mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.4V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 35ms Minimum |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Height | 2.45mm |
| Length | 10.47mm |
| Width | 7.959mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
MAX693CWE Overview
Power management is mounted through 16 terminals. Packaged in the form of a Tube, power management is easy to use. There are 1 functions included in this PMIC so that you can refer to them. It is possible to find on this power management a series of 1 channels. IC management is packaged as a 16-SOIC (0.295, 7.50mm Width) package. As with other Battery Backup Circuit products, this IC management also offers a wide range of benefits. Specifies a reflow peak temperature of 245 for the package during reflow. The supervisor is always powered by a 5V volt supply. IC management conducts in a 1-voltage supply. Using Surface Mount, IC management is mounted. There is a subcategory called Power Management Circuits for this power management. The total number of pins on this power management is 16. 16 pins are on the supervisor. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 4.5V. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. The recommended mounting type is Surface Mount. The supervisors should be set to the following temperature: 0°C~70°C TA. During normal operation, this power managment ic can generate Push-Pull, Push-Pull of output voltage. For this power management, there is an 10mA volt supply current. For similar manage ics search of the manufacturer, you can always refer to MAX693, the base PMIC number. In order to operate this power management, it requires 5V volts of power. The power management can work with a maximum supply temperature of 10mA.
MAX693CWE Features
Battery Backup Circuit type
Minimum supply voltage of 4.5V
10mA operating supply current
MAX693CWE Applications
There are a lot of Maxim Integrated MAX693CWE Voltage Supervisors applications.
- Smart meter
- FPGA design
- Efficient information transmission
- Insulation fault location system
- Transformer load monitoring equipment
- Dash board
- Military electronics
- Embedded computing
- Rechargeable batteries
- DC stabilized power supply module
