MAX694EPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX694 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.75V |
| Operating Supply Current | 10mA |
| Max Supply Current | 10mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX694EPA+ Overview
There are 8 terminals connected to this power management, which makes it easy to mount. Packaged in the form of a Tube, power management is easy to use. To assist you, this IC power includes 1 functions. It is possible to find on this power management a series of 1 channels. For your reference, this PMIC includes a list of 8-DIP (0.300, 7.62mm) functions. Compared to other Battery Backup Circuit products, this PMIC has a lot of benefits to offer. Specifies a reflow peak temperature of 260 for the package during reflow. When a supply voltage of 5V is applied to the power ic, it conducts. In a 1 supply voltage, the PMIC chip conducts. The mount is provided by Through Hole. There is a subcategory called Power Management Circuits for this power management. Power management has a total of 8 pins. 8 pins are on the supervisor. A voltage (Vsup) that doesn't fall below 4.75V as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. This IC power should be powered by no more than 5.5V volts of supply voltage (Vsup). The recommended mounting type is Through Hole. The temperature of the supervisors should be set to this range: -40°C~85°C TA. During operation, this power management system outputs Push-Pull, Totem Pole. There is a supply current of 10mA for the power management. You can always use MAX694, the base supervisor number, to search for similar PMICs of the manufacturer. It requires 5V watts of power to operate this voltage supervisor. A maximum supply temperature of 10mA can be used.
MAX694EPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 4.75V
10mA operating supply current
MAX694EPA+ Applications
There are a lot of Maxim Integrated MAX694EPA+ Voltage Supervisors applications.
- Personal computers
- Power distribution systems of CCU
- Power communication system
- Detection of phase sequence
- Consumer electronics
- Radar
- Smartphones
- DVR
- Electronics installed in the vehicle
- Radio
