MAX695CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Frequency | 250kHz |
| Base Part Number | MAX695 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.75V |
| Operating Supply Current | 350μA |
| Power Dissipation | 600mW |
| Max Supply Current | 10mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX695CPE+ Overview
This power management consists of 16 mounting terminals on which it can be mounted. Tube-packaging is used. In this PMIC, you can find 1 functions for your reference. Depending on the power managment ic you are looking at, you can find a total of 1 channels. The purpose of this IC power is to provide you with a reference of 16-DIP (0.300, 7.62mm) functions. Compared to other Battery Backup Circuit products, this PMIC has a lot of benefits to offer. During the reflow process, a peak temperature of 260 is specified for the package. When 5V is applied to the power ic, it conducts. Power management conducts at a voltage of 1. Through Hole mounts power management on the wall. Power Management Circuits is a subcategory of this PMIC chip. A total of 16 pins are located on this power management. 16 pins make up the power management. It is recommended that Vsup should not be less than 4.75V for this IC power. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. The recommended mounting type is Through Hole. The temperature of the supervisors should be set to this range: 0°C~70°C TA. When this power management system is in operation, it produces an output voltage of Push-Pull, Push-Pull. Supplied with a operating current of 350μA, this PMIC is capable of fully function as specified. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX695, which is the base power ics number. To be able to work, this power management requires 5V volts of power. The maximum supply temperature that PMIC chip can work with is 10mA. As a general rule, this IC management operates at a frequency of 250kHz, which is fine for most applications.
MAX695CPE+ Features
Battery Backup Circuit type
Minimum supply voltage of 4.75V
350μA operating supply current
MAX695CPE+ Applications
There are a lot of Maxim Integrated MAX695CPE+ Voltage Supervisors applications.
- Power distribution systems of operating room
- Automotive permanent magnet synchronous motors
- Electric heating appliances
- Dash board
- Leakage protection
- DC stabilized power supply module
- Utility meter
- Household appliances
- Smartphones
- Power distribution systems of ICU
