MAX695CWE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX695 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.75V |
| Operating Supply Current | 10mA |
| Max Supply Current | 10mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX695CWE+T Overview
Power management is mounted through 16 terminals. A Tape & Reel (TR) package is used to package the power management. Power management is possible to find a series of 1 functions. A series of 1 channels can be found on this supervisor. In this PMIC, you can find 16-SOIC (0.295, 7.50mm Width) functions for your reference. Several of the benefits of this PMIC are also shared by other Battery Backup Circuit products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. A supply voltage of 5V is used to conduct the PMIC chip. Power management conducts at a voltage of 1. The mount is attached to Surface Mount. There is a subcategory of this power ic known as Power Management Circuits. It has a total of 16 pins that are attached to IC management. This power management system has 16 pins. A voltage (Vsup) that doesn't fall below 4.75V as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.5V volts. The recommended mounting type is Surface Mount. It is recommended that the supervisor be set to this temperature: 0°C~70°C TA. During normal operation, this power managment ic can generate Push-Pull, Push-Pull of output voltage. There is a 10mA supply current present in the power management. You can always use MAX695, the base supervisor number, to search for similar PMICs of the manufacturer. In order to operate this power management, it requires 5V volts of power. A maximum supply temperature of 10mA can be used with this power management.
MAX695CWE+T Features
Battery Backup Circuit type
Minimum supply voltage of 4.75V
10mA operating supply current
MAX695CWE+T Applications
There are a lot of Maxim Integrated MAX695CWE+T Voltage Supervisors applications.
- Satellite navigation
- Digitally controlled LDO regulators circuit
- Military electronics
- Detection of phase sequence
- Transformer load monitoring equipment
- Power distribution systems of infant care room
- DC stabilized power supply module
- Telecommunications equipment
- Smart meter
- Detection of phase imbalance
