MAX695EWE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX695 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.75V |
| Operating Supply Current | 10mA |
| Max Supply Current | 10mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height | 2.25mm |
| Length | 10.47mm |
| Width | 7.39mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX695EWE+ Overview
This voltage supervisor has a total of 16 mounting terminals that can be used for mounting. In terms of packaging, power management follows the Tube model. To assist you, this IC power includes 1 functions. There are 1 channels available on this supervisor, and each channel has a different function. IC management is packaged as a 16-SOIC (0.295, 7.50mm Width) package. Several of the benefits of this PMIC are also shared by other Battery Backup Circuit products. The package peak reflow temperature is specified to be 260. The supervisor is always powered by a 5V volt supply. IC management conducts in a 1-voltage supply. The power management is mounted by a Surface Mount-axis. This power ic can be sub-categorized as Power Management Circuits. In total, the power management has 16 pins in it. 16 pins make up the power management. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 4.75V volts. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. Surface Mount is the recommended mounting type. We recommend setting the supervisors to -40°C~85°C TA degrees. During normal operation, this power managment ic can generate Push-Pull, Push-Pull of output voltage. The supply current of the power management is 10mA. You can always use MAX695, the base supervisor number, to search for similar PMICs of the manufacturer. The power management must be powered by 5V volts to function properly. The power management can work with a maximum supply temperature of 10mA.
MAX695EWE+ Features
Battery Backup Circuit type
Minimum supply voltage of 4.75V
10mA operating supply current
MAX695EWE+ Applications
There are a lot of Maxim Integrated MAX695EWE+ Voltage Supervisors applications.
- Embedded computing
- Power distribution systems of infant care room
- Precision measurement
- WiFi router
- Detection of phase loss
- Insulation fault location system
- Power distribution systems of ICU
- Network equipment
- Radio
- Detection of phase sequence
