MAX699CPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | WATCHDOG TIMER |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX699 |
| Output | Open Drain or Open Collector |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 5mA |
| Nominal Supply Current | 5mA |
| Max Supply Current | 5mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Threshold Voltage | +4.65V |
| Height | 4.45mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX699CPA+ Overview
There are 8 terminals on this power management that allow it to be mounted. Packaging is in the form of a Tube. As a reference, this IC management includes 1 functions for your convenience. A series of 1 channels can be found on this supervisor. In this IC management you will find 8-DIP (0.300, 7.62mm) functions for you to refer to. It is a IC power that shares many benefits with other products from the Simple Reset/Power-On Reset line. According to the specification, the package's peak reflow temperature is specified to be 260. During operation, the power ic is supplied with a voltage of 5V. A supply voltage of 1 is used to conduct the PMIC chip. Through Hole is the one that mounts power management. The power management belongs to the Power Management Circuits subcategory. Power management has a total of 8 pins. 8 pins are on the supervisor. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 3V. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. Power management recommends the Through Hole mounting type. This range of temperature should be set for the supervisors: 0°C~70°C TA. When this power management system is in operation, it produces an output voltage of Open Drain or Open Collector. The supply current of the power management is 5mA. There are also other features in the software such as [0], just to mention a few. You can always use MAX699, the base supervisor number, to search for similar PMICs of the manufacturer. This power management requires 3.3/5V power to work. At the most, voltage supervisor can work with a supply temperature of 5mA.
MAX699CPA+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 3V
5mA operating supply current
MAX699CPA+ Applications
There are a lot of Maxim Integrated MAX699CPA+ Voltage Supervisors applications.
- DVR
- Military communications
- Battery cars
- FPGA design
- Data storage applications
- Power distribution systems of CCU
- Efficient information transmission
- Power distribution systems of infant care room
- Personal computers
- Transformer load monitoring equipment
