MAX699CPA
| Parameters | |
|---|---|
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | WATCHDOG TIMER |
| Subcategory | Power Management Circuits |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX699 |
| Output | Open Drain or Open Collector |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3/5V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Channels | 1 |
| Adjustable Threshold | NO |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 5mA |
| Threshold Voltage | +4.65V |
| Height Seated (Max) | 4.572mm |
MAX699CPA Overview
This power management consists of 8 mounting terminals on which it can be mounted. It is packaged with Tube. The purpose of this IC management is to provide you with a reference of 1 functions. A series of 1 channels can be found on this supervisor. To assist you, this PMIC includes 8-DIP (0.300, 7.62mm) functions. This IC power shares lots of benefits with other Simple Reset/Power-On Reset products. Packages are specified to have an average peak reflow temperature of 245. When a supply voltage of 5V is applied to the power ic, it conducts. IC management conducts in a 1-voltage supply. This power ic can be sub-categorized as Power Management Circuits. In total, IC powers are 8 pins on the board. Through Hole is the recommended mounting type. It is recommended that the supervisor be set to this temperature: 0°C~70°C TA. While in operation, this supervisor has a voltage output of Open Drain or Open Collector. In addition, IC management are other features such as [0], to mention only a few. It is always advisable to use MAX699, the base supervisor number, when searching for similar PMICs from the manufacturer. In order to operate this power management, it requires 3.3/5V volts of power.
MAX699CPA Features
Simple Reset/Power-On Reset type
MAX699CPA Applications
There are a lot of Maxim Integrated MAX699CPA Voltage Supervisors applications.
- Urban rail transit weak current power monitoring
- Efficient information transmission
- Microprocessor system
- Dash board
- Electronics installed in the vehicle
- emergency room
- Insulation fault location system
- Unattended substation automation
- Personal computers
- Automotive permanent magnet synchronous motors
