MAX699CWE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | WATCHDOG TIMER |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX699 |
| Output | Open Drain, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 5mA |
| Max Supply Current | 5mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Threshold Voltage | +4.65V |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX699CWE+T Overview
It is mounted through 16 terminals on the power management. It is packaged with Tape & Reel (TR). The purpose of this IC management is to provide you with a reference of 1 functions. There are 1 channels available on this supervisor, and each channel has a different function. IC management is packaged as a 16-SOIC (0.295, 7.50mm Width) package. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. There is a specification for the peak reflow temperature of the package to be 260. IC management conducts at a voltage of 5V. A supply voltage of 1 is used to conduct the PMIC chip. By Surface Mount, IC management has been mounted. There is a subcategory called Power Management Circuits for this power management. A total of 16 pins are located on this power management. In order for this PMIC to work correctly, the minimum supply voltage (Vsup) should be greater than 3V. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. In this case, Surface Mount is the recommended mounting type. It is recommended that the supervisor be set to this temperature: 0°C~70°C TA. The output voltage of this power managment ic during operation is Open Drain, Push-Pull. For this power management, there is an 5mA volt supply current. Additionally, IC management are a variety of features, for example [0], to name a few. It is always advisable to use MAX699, the base supervisor number, when searching for similar PMICs from the manufacturer. The power management must be powered by 3.3/5V volts to function properly. The maximum supply temperature is 5mA.
MAX699CWE+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 3V
5mA operating supply current
MAX699CWE+T Applications
There are a lot of Maxim Integrated MAX699CWE+T Voltage Supervisors applications.
- Power distribution systems of ICU
- DSP
- Smartphones
- Utility meter
- Insulation fault location system
- Kitchen appliances
- Dash board
- Display equipment
- Leakage current detection
- Important electronics for automotive protection
