MAX703EPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX703 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 500μA |
| Max Supply Current | 500μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX703EPA+ Overview
This power management consists of 8 mounting terminals on which it can be mounted. Tube-packaging is used. As a reference, this IC management includes 1 functions for your convenience. This power management is made up of 1 channels which are available in a series format. The purpose of this IC power is to provide you with a reference of 8-DIP (0.300, 7.62mm) functions. There are many benefits that this IC power shares with other Battery Backup Circuit products as well. There is a specification for the peak reflow temperature of the package to be 260. The supervisor is always powered by a 5V volt supply. Power ics operate at 1 supply voltages. The mount is provided by Through Hole. There is a subcategory called Power Management Circuits for this power management. In total, IC powers are 8 pins on the board. 8 pins are present on the power management system. In order for this PMIC to work correctly, the minimum supply voltage (Vsup) should be greater than 0V. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. The recommended mounting type for IC management is Through Hole. The temperature of the supervisors should be set to this range: -40°C~85°C TA. There is an output voltage of Push-Pull, Totem Pole from this supervisor when it is operating. In order to maintain a stable supply current for the power management, 500μA is the recommended value. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX703, which is the base power ics number. There is a requirement for 5V power to power this power management. At the most, voltage supervisor can work with a supply temperature of 500μA.
MAX703EPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 0V
500μA operating supply current
MAX703EPA+ Applications
There are a lot of Maxim Integrated MAX703EPA+ Voltage Supervisors applications.
- Power distribution systems of ICU
- Unattended substation automation
- FPGA design
- Power communication system
- DC stabilized power supply module
- Consumer electronics
- Display equipment
- Smart meter
- Radio
- Electronics installed in the vehicle
