MAX704REPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX704 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.1V |
| Operating Supply Current | 50μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.625V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.07mA |
| Min Reset Threshold Voltage | 2.55V |
| Max Reset Threshold Voltage | 2.72V |
| Undervoltage Threshold | 2.55V |
| Overvoltage Threshold | 2.72V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX704REPA+ Overview
There are 8 terminals on this power management that allow it to be mounted. It is packaged with Tube. Please refer to this PMIC for 1 functions. There are 1 channels available on this supervisor, and each channel has a different function. Please refer to power management for 8-DIP (0.300, 7.62mm) functions. There are a number of benefits that this PMIC has in common with other Battery Backup Circuit manage ics. As specified in the package specification, the peak reflow temperature of the package is set at 260. IC management is possible to find a succession of 1 voltages that have been checked. Through Hole is the one that mounts power management. A IC power such as this can be classified as a Power Management Circuits power management system. It has a total of 8 pins that are attached to IC management. The pins of the power management system count 8. In order for this IC power to function, the supply voltage (Vsup) cannot be less than 1.1V. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. Power management recommends the Through Hole mounting type. We recommend setting the supervisors to -40°C~85°C TA degrees. During operation, this power management system outputs Push-Pull, Totem Pole. The power management's supply current is 50μA. To find similar IC managements from the manufacturer, you can always search by MAX704. It requires 3/5V watts of power to operate this voltage supervisor.
MAX704REPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 1.1V
50μA operating supply current
MAX704REPA+ Applications
There are a lot of Maxim Integrated MAX704REPA+ Voltage Supervisors applications.
- FPGA design
- Power distribution systems of CCU
- Detection of phase imbalance
- Rechargeable batteries
- Precision measurement
- Computer applications
- Microcontroller system
- Stable power system
- Medical-specific insulation monitor
- Leakage protection
