MAX704SESA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Base Part Number | MAX704 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.1V |
| Operating Supply Current | 50μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.925V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.05mA |
| Min Reset Threshold Voltage | 2.85V |
| Max Reset Threshold Voltage | 3.02V |
| Undervoltage Threshold | 2.85V |
| Overvoltage Threshold | 3.02V |
| Length | 4.9mm |
| Width | 3.9mm |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX704SESA Overview
Power management is mounted through 8 terminals. Tube-packaging is used. For your reference, this IC power includes a list of 1 functions. This power management is made up of 1 channels which are available in a series format. The purpose of this IC power is to provide you with a reference of 8-SOIC (0.154, 3.90mm Width) functions. Compared to other Battery Backup Circuit products, this PMIC has a lot of benefits to offer. During the reflow process, a peak temperature of 245 is specified for the package. During operation, the power ic is supplied with a voltage of 1. The mount is attached to Surface Mount. It is possible to subcategorize this power ic as a Power Management Circuits chip. 8 pins are present in total in this power management. There are 8 pins on the power managment ic. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1.1V. There should be no more than 5.5V volts of supply voltage (Vsup) in this power management. Surface Mount is the recommended mounting type. You should set the supervisor's temperature during -40°C~85°C TA . When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. There is a supply current of 50μA for the power management. A similar IC managements number of the manufacturer can always be found by using MAX704, the base power ics number. The power management must be powered by 3.3/5V volts to function properly.
MAX704SESA Features
Battery Backup Circuit type
Minimum supply voltage of 1.1V
50μA operating supply current
MAX704SESA Applications
There are a lot of Maxim Integrated MAX704SESA Voltage Supervisors applications.
- Medical-specific insulation monitor
- emergency room
- DSP
- Detection of phase sequence
- Rechargeable batteries
- DVR
- Embedded computing
- Battery-powered equipment
- Computer applications
- Electric heating appliances
