MAX705CSA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX705 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 150μA |
| Power Dissipation | 471mW |
| Max Supply Current | 350μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX705CSA Overview
This voltage supervisor has a total of 8 mounting terminals that can be used for mounting. Tube-packaging is used. To assist you, this IC power includes 1 functions. On this supervisor, there is a series of 2 channels that can be found. Please refer to power management for 8-SOIC (0.154, 3.90mm Width) functions. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. Specifies a reflow peak temperature of 245 for the package during reflow. The supervisor is always powered by a 5V volt supply. There is a voltage supply of 1 for the PMIC chip, and the chip conducts at that voltage. Surface Mount mounts power management on the wall. The power management system can be categorized as a Power Management Circuits chip. In total, the power management has 8 pins in it. Power managment ic pin count is 8. Supply voltage (Vsup) should be at least 1V for this power management. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Surface Mount mounting is recommended. This power management is the recommended temperature range for the supervisors: 0°C~70°C TA. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. The power management's supply current is 350μA. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX705, which is the base power ics number. The power management must be powered by 5V volts to function properly. The power management can work with a maximum supply temperature of 350μA.
MAX705CSA Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
350μA operating supply current
MAX705CSA Applications
There are a lot of Maxim Integrated MAX705CSA Voltage Supervisors applications.
- Power distribution systems of ICU
- Data storage applications
- Leakage protection
- Automotive power systems
- Important electronics for automotive safety
- Electronics installed in the vehicle
- Battery-powered equipment
- Electrical fire monitoring system
- Magnetic resonance imaging
- Radar
