MAX705CSA-T
| Parameters | |
|---|---|
| Max Supply Current | 350μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX705 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 350μA |
MAX705CSA-T Overview
This voltage supervisor has a total of 8 mounting terminals that can be used for mounting. Tape & Reel (TR)-packaging is used. In this IC power you will find 1 functions for you to refer to. This power management is made up of 2 channels which are available in a series format. There are 8-SOIC (0.154, 3.90mm Width) functions included in this PMIC so that you can refer to them. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. The package peak reflow temperature is specified to be 260. A supply voltage of 5V is used to conduct the PMIC chip. In a 1 supply voltage, the PMIC chip conducts. Power management is included in the Surface Mount mount. It is possible to subcategorize this power ic as a Power Management Circuits chip. Taking into account all of the pins, this power management has a total of 8. The pins of the power management system count 8. It is recommended that Vsup should not be less than 1V for this IC power. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. A Surface Mount mounting type is recommended. The supervisors should be set to the following temperature: 0°C~70°C TA. As a result of this supervisor's operation, the output voltage is Push-Pull, Totem Pole. Supplied with a operating current of 350μA, this PMIC is capable of fully function as specified. It is always advisable to use MAX705, the base supervisor number, when searching for similar PMICs from the manufacturer. The voltage supervisor requires a power source of 5V volts in order to work correctly. Voltage supervisor can work with a supply temperature of 350μA at the most.
MAX705CSA-T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
350μA operating supply current
MAX705CSA-T Applications
There are a lot of Maxim Integrated MAX705CSA-T Voltage Supervisors applications.
- Battery cars
- Radio
- Solar power charger
- Automotive permanent magnet synchronous motors
- emergency room
- Power distribution systems of ICU
- Battery cars
- Display equipment
- Detection of phase sequence
- Embedded computing
