MAX705CUA+
| Parameters | |
|---|---|
| Operating Supply Current | 350μA |
| Max Supply Current | 350μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height | 950μm |
| Length | 3.1mm |
| Width | 3.1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX705 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
MAX705CUA+ Overview
Power management is mounted through 8 terminals. Packaging is in the form of a Tube. Power management is possible to find a series of 1 functions. There are 1 channels on this power managment ic that can be found in a series. For your reference, this PMIC includes a list of 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) functions. It is a IC power that shares many benefits with other products from the Simple Reset/Power-On Reset line. Specifies a reflow peak temperature of 260 for the package during reflow. When 5V is applied to the power ic, it conducts. Power management conducts at a voltage of 1. The power management is mounted by a Surface Mount-axis. The power management system can be categorized as a Power Management Circuits chip. There are a total of 8 pins on power management. Power managment ic pin count is 8. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1V volts. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. A Surface Mount mounting type is recommended. You should set the supervisor's temperature during 0°C~70°C TA . The output voltage of this power managment ic during operation is Push-Pull, Totem Pole. The supply current of the power management is 350μA. For similar manage ics search of the manufacturer, you can always refer to MAX705, the base PMIC number. A power supply of 5V watts is required for the operation of this power management. The maximum supply temperature that PMIC chip can work with is 350μA.
MAX705CUA+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
350μA operating supply current
MAX705CUA+ Applications
There are a lot of Maxim Integrated MAX705CUA+ Voltage Supervisors applications.
- Battery-powered equipment
- Consumer electronics
- Refrigeration
- Rechargeable batteries
- Analog circuit
- Radio
- Microprocessor system
- Insulation fault location system
- WiFi router
- Solar power charger
