MAX705ESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX705 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 500μA |
| Max Supply Current | 500μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX705ESA+T Overview
As you can see, this power management is mounted through 8 terminals. Packaged in the form of a Tape & Reel (TR), power management is easy to use. As a reference, this IC management includes 1 functions for your convenience. Depending on the power managment ic you are looking at, you can find a total of 2 channels. There are 8-SOIC (0.154, 3.90mm Width) functions included in this PMIC so that you can refer to them. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. As specified in the package specification, the peak reflow temperature of the package is set at 260. There is a voltage supply of 5V for the PMIC chip, and the chip conducts at that voltage. A supply voltage of 1 is used to conduct the PMIC chip. Surface Mount is the one that mounts power management. It is possible to subcategorize this power ic as a Power Management Circuits chip. It has a total of 8 pins that are attached to IC management. Pin count of the power management is 8. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 1.2V, which is the minimum supply voltage that should be applied. It is recommended that the maximum supply voltage (Vsup) in this IC power be no more than 5.5V volts. Power management' mounting is recommended to be done with the Surface Mount type of mounting. We recommend setting the supervisors to -40°C~85°C TA degrees. As this power managment ic operates, it is able to produce an output voltage of Push-Pull, Totem Pole. For this power management, there is an 500μA volt supply current. A similar IC managements number of the manufacturer can always be found by using MAX705, the base power ics number. There is a requirement for 5V power to power this power management. The power management can work with a maximum supply temperature of 500μA.
MAX705ESA+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
500μA operating supply current
MAX705ESA+T Applications
There are a lot of Maxim Integrated MAX705ESA+T Voltage Supervisors applications.
- Urban rail transit weak current power monitoring
- Telecommunications equipment
- emergency room
- Power distribution systems of ICU
- Important electronics for automotive protection
- Utility meter
- Automotive power systems
- Kitchen appliances
- Detection of phase loss
- Fire equipment power monitoring system
