MAX706ATESA+T
| Parameters | |
|---|---|
| Min Supply Voltage | 1.2V |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 3.08V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.5mA |
| Min Reset Threshold Voltage | 3V |
| Max Reset Threshold Voltage | 3.15V |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | WATCHDOG TIMER, MANUAL RESET, POWER FAIL COMPARATOR |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 470.6mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX706 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
MAX706ATESA+T Overview
There are 8 terminals connected to this power management, which makes it easy to mount. In terms of packaging, power management follows the Tape & Reel (TR) model. The purpose of this IC management is to provide you with a reference of 1 functions. Power management consists of 1 channels, each of which can be used independently. For your reference, this PMIC includes a list of 8-SOIC (0.154, 3.90mm Width) functions. There are a lot of similarities between this IC power and other Simple Reset/Power-On Reset products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. A supply voltage of 3V is used to conduct the PMIC chip. Power management conducts at a voltage of 1. Surface Mount is the one that mounts power management. There is a subcategory called Power Management Circuits for this power management. In total, IC powers are 8 pins on the board. There are 8 pins on the power managment ic. A voltage (Vsup) that doesn't fall below 1.2V as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. The mounting type of the supervisors is Surface MountThe temperature of the supervisors should be set to this range: -40°C~85°C TA. While in operation, this supervisor has a voltage output of Push-Pull, Totem Pole. Supervisors are also additional features, such as [0] for example, which are worth mentioning. A similar IC managements number of the manufacturer can always be found by using MAX706, the base power ics number. To operate this power management, you will need at least 3.3/5V volts of power.
MAX706ATESA+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
MAX706ATESA+T Applications
There are a lot of Maxim Integrated MAX706ATESA+T Voltage Supervisors applications.
- Detection of phase loss
- Automotive permanent magnet synchronous motors
- Network equipment
- Battery-powered equipment
- Electric heating appliances
- Embedded computing
- Fire equipment power monitoring system
- Electrical fire monitoring system
- Computer applications
- Leakage protection
