MAX706CSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX706 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Max Output Current | 20mA |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 150μA |
| Power Dissipation | 471mW |
| Max Supply Current | 350μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.4V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX706CSA+ Overview
As you can see, this power management is mounted through 8 terminals. Tube-packaging is used. In this PMIC, you can find 1 functions for your reference. On this supervisor, there is a series of 2 channels that can be found. There are 8-SOIC (0.154, 3.90mm Width) functions included in this PMIC so that you can refer to them. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. Specifies a reflow peak temperature of 260 for the package during reflow. The supervisor is always powered by a 5V volt supply. IC management conducts in a 1-voltage supply. The mount is provided by Surface Mount. Power Management Circuits is a subcategory of this PMIC chip. In total, IC powers are 8 pins on the board. 8 pins make up the power management. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 1V, which is the minimum supply voltage that should be applied. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. Power management recommends the Surface Mount mounting type. The supervisors should be set to the following temperature: 0°C~70°C TA. The output voltage of this power managment ic during operation is Push-Pull, Totem Pole. There is a 350μA supply current present in the power management. It is always advisable to use MAX706, the base supervisor number, when searching for similar PMICs from the manufacturer. A power supply of 5V watts is required for the operation of this power management. The maximum supply temperature that PMIC chip can work with is 350μA.
MAX706CSA+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
350μA operating supply current
MAX706CSA+ Applications
There are a lot of Maxim Integrated MAX706CSA+ Voltage Supervisors applications.
- DVR
- Rechargeable batteries
- emergency room
- Detection of phase imbalance
- Automotive permanent magnet synchronous motors
- Refrigeration
- Computer applications
- Consumer electronics
- Efficient information transmission
- Electronics installed in the vehicle
