MAX706EUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX706 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 500μA |
| Max Supply Current | 500μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.4V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX706EUA+T Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 8 in total. In terms of packaging, power management follows the Tape & Reel (TR) model. There are 1 functions included in this PMIC so that you can refer to them. This power managment ic consists of 2 channels, each of which can be used independently. Please refer to power management for 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) functions. There are a lot of similarities between this IC management and other Simple Reset/Power-On Reset products. Specifies a reflow peak temperature of 260 for the package during reflow. The supervisor is always powered by a 5V volt supply. Power management conducts at a voltage of 1. Power management is included in the Surface Mount mount. The power management system can be categorized as a Power Management Circuits chip. A total of 8 pins are located on this power management. 8 pins are present on the power management system. It is recommended that Vsup should not be less than 1.2V for this IC power. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. Surface Mount is the recommended mounting type. It is recommended that the supervisor be set to this temperature: -40°C~85°C TA. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. There is a 500μA supply current present in the power management. You can always use MAX706, the base supervisor number, to search for similar PMICs of the manufacturer. To be able to work, this power management requires 5V volts of power. The maximum supply temperature is 500μA.
MAX706EUA+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
500μA operating supply current
MAX706EUA+T Applications
There are a lot of Maxim Integrated MAX706EUA+T Voltage Supervisors applications.
- Urban rail transit weak current power monitoring
- Transformer load monitoring equipment
- Leakage current detection
- Important electronics for automotive protection
- Display equipment
- DVR
- Medical-specific isolation transformer
- Battery cars
- FPGA design
- Radar
