MAX706PCSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | WATCHDOG TIMER, MANUAL RESET, POWER FAIL COMPARATOR |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 470.6mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | MAX706 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 3 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 135μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High |
| Voltage - Threshold | 2.63V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.35mA |
| Min Reset Threshold Voltage | 2.55V |
| Max Reset Threshold Voltage | 2.7V |
| Undervoltage Threshold | 2.55V |
| Overvoltage Threshold | 2.7V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX706PCSA+ Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 8 in total. In terms of packaging, power management follows the Tube model. Please find attached 1 functions for your reference in this IC power. On this supervisor, there is a series of 3 channels that can be found. In this IC management you will find 8-SOIC (0.154, 3.90mm Width) functions for you to refer to. It is a IC power that shares many benefits with other products from the Simple Reset/Power-On Reset line. Packages are specified to have an average peak reflow temperature of 260. The supervisor is always powered by a 3V volt supply. A supply voltage of 1 is used to conduct the PMIC chip. Power management is included in the Surface Mount mount. A IC power such as this can be classified as a Power Management Circuits power management system. 8 pins are present in total in this power management. The pins of the power management system count 8. It is recommended that Vsup should not be less than 1V for this IC power. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. Power management recommends the Surface Mount mounting type. The supervisors should be set to the following temperature: 0°C~70°C TA. Power management has an output of Push-Pull, Totem Pole during operation. As far as the supply current of the power management is concerned, it is 135μA. Power management is also possible to add other features such as WATCHDOG TIMER, MANUAL RESET, POWER FAIL COMPARATOR to name a few. For similar manage ics search of the manufacturer, you can always refer to MAX706, the base PMIC number. It is necessary to have 3.3/5V volts of power in order for this voltage supervisor to operate.
MAX706PCSA+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
135μA operating supply current
MAX706PCSA+ Applications
There are a lot of Maxim Integrated MAX706PCSA+ Voltage Supervisors applications.
- Set top box
- DSP
- Detection of phase loss
- Battery cars
- Battery cars
- Transformer load monitoring equipment
- Military electronics
- Power distribution systems of ICU
- Utility meter
- Solar power charger
