MAX707ESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX707 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 500μA |
| Max Supply Current | 500μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Threshold Voltage | +4.65V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Length | 4.9mm |
| Width | 3.9mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX707ESA+T Overview
This power management consists of 8 mounting terminals on which it can be mounted. Power management is packaged in a Tape & Reel (TR) way. There are 1 functions included in this PMIC so that you can refer to them. A series of 2 channels can be found on this supervisor. There are 8-SOIC (0.154, 3.90mm Width) functions included in this PMIC so that you can refer to them. As with other Simple Reset/Power-On Reset products, this IC management also offers a wide range of benefits. As specified in the package specification, the peak reflow temperature of the package is set at 260. A supply voltage of 5V is used to conduct the PMIC chip. IC management is possible to find a succession of 1 voltages that have been checked. The mount is attached to Surface Mount. It is possible to subcategorize this power ic as a Power Management Circuits chip. In total, it has 8 pins on IC management. There are 8 pins on the supervisor. In order for this PMIC to work correctly, the minimum supply voltage (Vsup) should be greater than 1.2V. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. The mounting type of the supervisors is Surface MountWe recommend setting the supervisors to -40°C~85°C TA degrees. During normal operation, this power managment ic can generate Push-Pull, Push-Pull of output voltage. As far as the supply current of the power management is concerned, it is 500μA. You can always use MAX707, the base supervisor number, to search for similar PMICs of the manufacturer. To operate this power management, you will need at least 5V volts of power. At the most, voltage supervisor can work with a supply temperature of 500μA.
MAX707ESA+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
500μA operating supply current
MAX707ESA+T Applications
There are a lot of Maxim Integrated MAX707ESA+T Voltage Supervisors applications.
- Data storage applications
- Refrigeration
- Cloud computing
- Power distribution systems of operating room
- Urban rail transit weak current power monitoring
- Computer applications
- Detection of phase imbalance
- Satellite navigation
- Electronics installed in the vehicle
- DSP
