MAX708TEPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | MANUAL RESET, POWER FAIL COMPARATOR |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727.3mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX708 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 135μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active High/Active Low |
| Voltage - Threshold | 3.08V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.5mA |
| Min Reset Threshold Voltage | 3V |
| Max Reset Threshold Voltage | 3.15V |
| Threshold Voltage | +3.08V |
| Undervoltage Threshold | 3V |
| Overvoltage Threshold | 3.15V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX708TEPA+ Overview
This voltage supervisor has a total of 8 mounting terminals that can be used for mounting. Tube-packaging is used. As a reference, this IC management includes 1 functions for your convenience. This power managment ic consists of 1 channels, each of which can be used independently. In this PMIC, you can find 8-DIP (0.300, 7.62mm) functions for your reference. As with other Simple Reset/Power-On Reset products, this IC management also offers a wide range of benefits. There is a specification for the peak reflow temperature of the package to be 245. During operation, the power ic is supplied with a voltage of 3V. When 1 is applied to the power ic, it conducts. Power management is included in the Through Hole mount. It is possible to subcategorize this power ic as a Power Management Circuits chip. There are a total of 8 pins on power management. There are 8 pins on the power managment ic. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1.2V volts. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. Power management recommends the Through Hole mounting type. You should set the supervisor's temperature during -40°C~85°C TA . There is an output voltage of Push-Pull, Push-Pull from this supervisor when it is operating. There is a supply current of 135μA for the power management. The other features include, for example, [0], which is just one example. For similar manage ics search of the manufacturer, you can always refer to MAX708, the base PMIC number. There is a requirement for 5V power to power this power management.
MAX708TEPA+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
135μA operating supply current
MAX708TEPA+ Applications
There are a lot of Maxim Integrated MAX708TEPA+ Voltage Supervisors applications.
- Utility meter
- Smartphones
- Power distribution systems of operating room
- Power distribution systems of infant care room
- Consumer electronics
- Set top box
- Detection of phase loss
- Power distribution systems of CCU
- Dash board
- Microcontroller system
