MAX776CSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Base Part Number | MAX776 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | -15V |
| Output Type | Transistor Driver |
| Max Output Current | 150mA |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Negative |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | 3V~16.5V |
| Control Features | Enable |
| Max Output Voltage | -14.4V |
| Topology | Buck-Boost |
| Min Input Voltage | 3V |
| Control Mode | CURRENT-MODE |
| Max Input Voltage | 16.5V |
| Control Technique | PULSE FREQUENCY MODULATION |
| Synchronous Rectifier | No |
| Min Output Voltage | -15.6V |
| Max Frequency | 300kHz |
| Nominal Output Voltage | -15V |
| Duty Cycle | 85 % |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX776CSA+ Overview
Capsuled in the 8-SOIC (0.154, 3.90mm Width) package, the switching controller suits most application needs. For 1 outputs, the dc motor controller is appropriate. PMIC packaging is solid with a Tube enclosure. With this function, you can deal with Transistor Driver dc switching's outputs (s). The supply and operating voltage of the dc control are 3V~16.5V. Qualified to work in an dc switcher with 0°C~70°C TA. The Surface Mount allows it to be used for dc dc regulator in general. Switching control is made easier with the dcdc regulator's Enable. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. A switching converters's terminal (s) sits at the DUAL position. A variety of 8 terminations are available in dc switching. Some of the control techniques used by these dc dc converter ics are PULSE FREQUENCY MODULATION. DC switcher's voltage input of 5V. You can find other relevant dc to dc converter ics by searching "MAX776". Pins number 8 of switching converter in total. In particular, switching converter is a type of Switching Regulator or Controllers. DC regulator outputs -15V voltage based on test statistics. You should note that the dc dc regulator's usual output current is 1A. Having a Surface Mount makes DC switcher ideal for most prototype and application designs. There is a maximum frequency of 300kHz on this dc regulators. Since the dc switcher's maximum input voltage is 16.5V, the voltage must be regulated accordingly. Voltage 3V must be supplied. There will be 150mA current output from the dc switcher above 150mA. The datasheet indicates that the switching converter can output -14.4V volts at its maximum. Its lowest voltage output is not less than -15.6V.
MAX776CSA+ Features
Transistor Driver Outputs
Enable
PULSE FREQUENCY MODULATION
MAX776CSA+ Applications
There are a lot of Maxim Integrated MAX776CSA+ DC to DC converter applications.
- Medical monitoring systems
- Laboratories
- Refrigerators of central air conditioners
- Hydraulic presses
- Smart grid
- CMM
- Flexible manufacturing cells
- Gear/thread machining machines
- Arc suppression circuits
- Sink circuits
