MAX791CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX791 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 16 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 65μA |
| Max Supply Current | 150μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX791CPE+ Overview
Power management is mounted through 16 terminals. Packaging is in the form of a Tube. Power management is possible to find a series of 1 functions. There are 1 channels on this power managment ic that can be found in a series. In this PMIC, you can find 16-DIP (0.300, 7.62mm) functions for your reference. This IC power shares lots of benefits with other Battery Backup Circuit products. There is a specification for the peak reflow temperature of the package to be 260. IC management conducts in a 5V-voltage supply. When a supply voltage of 1 is applied to the power ic, it conducts. The mount is attached to Through Hole. Power Management Circuits is a subcategory of this PMIC chip. Power management has a total of 16 pins. There are 16 pins on the supervisor. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 0V, which is the minimum supply voltage that should be applied. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Mounting type Through Hole is recommended. This power management is the recommended temperature range for the supervisors: 0°C~70°C TA. As a result of this supervisor's operation, the output voltage is Push-Pull, Totem Pole. There is a 65μA supply current present in the power management. It is always advisable to use MAX791, the base supervisor number, when searching for similar PMICs from the manufacturer. It requires 5V watts of power to operate this voltage supervisor. The power management can work with a maximum supply temperature of 150μA.
MAX791CPE+ Features
Battery Backup Circuit type
Minimum supply voltage of 0V
65μA operating supply current
MAX791CPE+ Applications
There are a lot of Maxim Integrated MAX791CPE+ Voltage Supervisors applications.
- Utility meter
- Transformer load monitoring equipment
- Electrical fire monitoring system
- Dash board
- Microcontroller system
- Radar
- Microprocessor system
- Embedded computing
- Display equipment
- Multi-voltage system
