MAX792LCSE+T
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | MAX792 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.75V |
| Operating Supply Current | 150μA |
| Max Supply Current | 150μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.62V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX792LCSE+T Overview
There are 16 terminals on this power management that allow it to be mounted. Packaged in the form of a Tape & Reel (TR), power management is easy to use. Power management is possible to find a series of 1 functions. There are 1 channels on this power managment ic that can be found in a series. There are 16-SOIC (0.154, 3.90mm Width) functions included in this PMIC so that you can refer to them. Several of the benefits of this PMIC are also shared by other Simple Reset/Power-On Reset products. The package peak reflow temperature is specified to be 260. Manage ics operate at 3V supply voltages. Power ics operate at 1 supply voltages. Surface Mount mounts IC management. The power management belongs to the Power Management Circuits subcategory. In total, IC powers are 16 pins on the board. There are 16 pins on the power managment ic. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 2.75V. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. Surface Mount mounting is recommended. The temperature of the supervisors should be set to this range: 0°C~70°C TA. While in operation, this supervisor has a voltage output of Push-Pull, Push-Pull. In order to maintain a stable supply current for the power management, 150μA is the recommended value. You can always use MAX792, the base supervisor number, to search for similar PMICs of the manufacturer. It is necessary to have 3/5V volts of power in order for this voltage supervisor to operate. If you want to work with PMIC chip, you will need to supply PMIC chip with a temperature at least of 150μA.
MAX792LCSE+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 2.75V
150μA operating supply current
MAX792LCSE+T Applications
There are a lot of Maxim Integrated MAX792LCSE+T Voltage Supervisors applications.
- Fire equipment power monitoring system
- Refrigeration
- Solar power charger
- Display equipment
- Detection of phase loss
- Battery cars
- Detection of phase sequence
- DSP
- Power distribution systems of operating room
- Consumer electronics
