MAX793SCPE+
| Parameters | |
|---|---|
| Pin Count | 16 |
| Power Supplies | 3.3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 62μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 2.925V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.08mA |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX793 |
| Output | Open Drain, Push-Pull |
MAX793SCPE+ Overview
This power management consists of 16 mounting terminals on which it can be mounted. In terms of packaging, power management follows the Tube model. For your reference, this IC power includes a list of 1 functions. On this supervisor, there is a series of 2 channels that can be found. As a reference, this IC power includes 16-DIP (0.300, 7.62mm) functions for your convenience. Several of the benefits of this PMIC are also shared by other Battery Backup Circuit products. The package peak reflow temperature is specified to be 260. During operation, the power ic is supplied with a voltage of 3.3V. A supply voltage of 1 is used to conduct the PMIC chip. By Through Hole, IC management has been mounted. As a subcategory, this PMIC chip can be categorized as Power Management Circuits. In total, IC powers are 16 pins on the board. There are 16 pins on the supervisor. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. A Through Hole mounting type is recommended. You should set the supervisor's temperature during 0°C~70°C TA . While this power management is operating, it will output Open Drain, Push-Pull as the output voltage. The power management's supply current is 62μA. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX793, which is the base power ics number. The voltage supervisor requires a power source of 3.3/5V volts in order to work correctly.
MAX793SCPE+ Features
Battery Backup Circuit type
Minimum supply voltage of 1V
62μA operating supply current
MAX793SCPE+ Applications
There are a lot of Maxim Integrated MAX793SCPE+ Voltage Supervisors applications.
- Power distribution systems of CCU
- Important electronics for automotive protection
- Telecommunications equipment
- Transformer load monitoring equipment
- Precision measurement
- Electronics installed in the vehicle
- Battery cars
- emergency room
- Embedded computing
- FPGA design
