MAX793SCSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 696mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | MAX793 |
| Output | Open Drain, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 3.3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 62μA |
| Nominal Supply Current | 62μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 2.925V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.08mA |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX793SCSE+ Overview
A total of 16 terminals are used to mount this power management. It is packaged with Tube. There are 1 functions included in this PMIC so that you can refer to them. Depending on the power managment ic you are looking at, you can find a total of 2 channels. The purpose of this IC power is to provide you with a reference of 16-SOIC (0.154, 3.90mm Width) functions. Compared to other Battery Backup Circuit products, this PMIC has a lot of benefits to offer. As specified in the package specification, the peak reflow temperature of the package is set at 260. During operation, the power ic is supplied with a voltage of 3.3V. When 1 is applied to the power ic, it conducts. Surface Mount mounts power management on the wall. The power management system can be categorized as a Power Management Circuits chip. In total, the power management has 16 pins in it. 16 pins make up the power management. Supply voltage (Vsup) should be at least 1V for this power management. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.5V volts. The recommended mounting type is Surface Mount. You should set the supervisor's temperature during 0°C~70°C TA . During operation, this power management system outputs Open Drain, Push-Pull. It is estimated that the voltage supervisor's supply current is 62μA. A similar IC managements number of the manufacturer can always be found by using MAX793, the base power ics number. It requires 3.3/5V watts of power to operate this voltage supervisor.
MAX793SCSE+ Features
Battery Backup Circuit type
Minimum supply voltage of 1V
62μA operating supply current
MAX793SCSE+ Applications
There are a lot of Maxim Integrated MAX793SCSE+ Voltage Supervisors applications.
- Detection of phase imbalance
- Leakage current detection
- Power communication system
- Computer applications
- Important electronics for automotive protection
- Analog circuit
- Power distribution systems of CCU
- Digitally controlled LDO regulators circuit
- Linux and server computing
- Military communications
