MAX793SCSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 696mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | MAX793 |
| Output | Open Drain, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 3.3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 62μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 2.925V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.08mA |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX793SCSE+T Overview
This voltage supervisor has a total of 16 mounting terminals that can be used for mounting. Power management is packaged in a Tape & Reel (TR) way. To assist you, this IC power includes 1 functions. There are 2 channels available on this supervisor, and each channel has a different function. In this IC management you will find 16-SOIC (0.154, 3.90mm Width) functions for you to refer to. There are a lot of similarities between this IC power and other Battery Backup Circuit products. According to the specification, the package's peak reflow temperature is specified to be 260. When 3.3V is applied to the power ic, it conducts. During operation, the power ic is supplied with a voltage of 1. The mount is provided by Surface Mount. A IC power such as this can be classified as a Power Management Circuits power management system. A total of 16 pins are located on this power management. There are 16 pins on the supervisor. In order for this PMIC to work correctly, the minimum supply voltage (Vsup) should be greater than 1V. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. Power management recommends the Surface Mount mounting type. This range of temperature should be set for the supervisors: 0°C~70°C TA. As a result of this supervisor's operation, the output voltage is Open Drain, Push-Pull. Supplied with a operating current of 62μA, this PMIC is capable of fully function as specified. A similar IC managements number of the manufacturer can always be found by using MAX793, the base power ics number. The power management must be powered by 3.3/5V volts to function properly.
MAX793SCSE+T Features
Battery Backup Circuit type
Minimum supply voltage of 1V
62μA operating supply current
MAX793SCSE+T Applications
There are a lot of Maxim Integrated MAX793SCSE+T Voltage Supervisors applications.
- Digitally controlled LDO regulators circuit
- Sensitive sensors
- DVR
- Insulation fault location system
- Refrigeration
- emergency room
- Electric heating appliances
- Battery-powered equipment
- Consumer electronics
- Multi-voltage system
