MAX793SESE
| Parameters | |
|---|---|
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | MAX793 |
| Output | Open Drain, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 3.3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.1V |
| Operating Supply Current | 62μA |
| Nominal Supply Current | 62μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 2.925V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.08mA |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
MAX793SESE Overview
Power management is mounted through 16 terminals. Tube-packaging is used. To assist you, this IC power includes 1 functions. On this supervisor, there is a series of 2 channels that can be found. To assist you, this PMIC includes 16-SOIC (0.154, 3.90mm Width) functions. As with other Battery Backup Circuit products, this IC management also offers a wide range of benefits. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 245. A supply voltage of 3.3V is used to conduct the PMIC chip. When a supply voltage of 1 is applied to the power ic, it conducts. The power management is mounted by Surface Mount. A IC power such as this can be classified as a Power Management Circuits power management system. A total of 16 pins are located on this power management. This power management has 16 pins. There should be a minimum voltage supply (Vsup) of 1.1V for this PMIC. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. Mounting type Surface Mount is recommended. It is recommended to set the supervisor's temperature to this range: -40°C~85°C TA. There is an output voltage of Open Drain, Push-Pull from this supervisor when it is operating. The power management's supply current is 62μA. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX793, which is the base power ics number. A power supply of 3.3/5V watts is required for the operation of this power management.
MAX793SESE Features
Battery Backup Circuit type
Minimum supply voltage of 1.1V
62μA operating supply current
MAX793SESE Applications
There are a lot of Maxim Integrated MAX793SESE Voltage Supervisors applications.
- Detection of phase imbalance
- FPGA design
- DSP
- Efficient information transmission
- Kitchen appliances
- Leakage protection
- Power communication system
- Household appliances
- Insulation fault location system
- Consumer electronics
