MAX794ESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 696mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | MAX794 |
| Output | Open Drain, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.1V |
| Operating Supply Current | 62μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | Adjustable/Selectable |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.08mA |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX794ESE+T Overview
Power management is mounted through 16 terminals. Power management is packaged in a Tape & Reel (TR) way. The purpose of this IC management is to provide you with a reference of 1 functions. Depending on the power managment ic you are looking at, you can find a total of 2 channels. Please refer to power management for 16-SOIC (0.154, 3.90mm Width) functions. Compared to other Battery Backup Circuit products, this PMIC has a lot of benefits to offer. Specifies a reflow peak temperature of 260 for the package during reflow. During operation, the power ic is supplied with a voltage of 3V. When 1 is applied to the power ic, it conducts. Power management is included in the Surface Mount mount. This power ic can be sub-categorized as Power Management Circuits. 16 pins are present in total in this power management. Power managment ic pin count is 16. It is recommended that Vsup should not be less than 1.1V for this IC power. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. A Surface Mount mounting type is recommended. We recommend setting the supervisors to -40°C~85°C TA degrees. The output voltage of this power managment ic during operation is Open Drain, Push-Pull. The power management's supply current is 62μA. It is always advisable to use MAX794, the base supervisor number, when searching for similar PMICs from the manufacturer. The power management must be powered by 3/5V volts to function properly.
MAX794ESE+T Features
Battery Backup Circuit type
Minimum supply voltage of 1.1V
62μA operating supply current
MAX794ESE+T Applications
There are a lot of Maxim Integrated MAX794ESE+T Voltage Supervisors applications.
- Computer applications
- Sensitive sensors
- Multi-voltage system
- DC stabilized power supply module
- Dash board
- Important electronics for automotive safety
- Radar
- Electronics installed in the vehicle
- Military communications
- Battery cars
