MAX795TCPA+
| Parameters | |
|---|---|
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 3.075V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.07mA |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX795 |
| Output | Open Drain or Open Collector |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 49μA |
MAX795TCPA+ Overview
As you can see, this power management is mounted through 8 terminals. Power management is packaged in a Tube way. In this IC power you will find 1 functions for you to refer to. Power management consists of 2 channels, each of which can be used independently. Please find attached 8-DIP (0.300, 7.62mm) functions for your reference in this IC power. There are a lot of similarities between this IC power and other Battery Backup Circuit products. According to the specification, the package's peak reflow temperature is specified to be 260. During operation, the power ic is supplied with a voltage of 3.3V. When 1 is applied to the power ic, it conducts. The power management is mounted by a Through Hole-axis. It is possible to subcategorize this power ic as a Power Management Circuits chip. In total, the power management has 8 pins in it. 8 pins make up the power management. It is recommended that Vsup should not be less than 1V for this IC power. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Power management recommends the Through Hole mounting type. It is recommended to set the supervisor's temperature to this range: 0°C~70°C TA. The output voltage of this power managment ic during operation is Open Drain or Open Collector. The power management's supply current is 49μA. You can always use MAX795, the base supervisor number, to search for similar PMICs of the manufacturer. A power supply of 3.3/5V watts is required for the operation of this power management.
MAX795TCPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 1V
49μA operating supply current
MAX795TCPA+ Applications
There are a lot of Maxim Integrated MAX795TCPA+ Voltage Supervisors applications.
- Microprocessor system
- Set top box
- Smart meter
- Leakage current detection
- Sensitive sensors
- Automotive permanent magnet synchronous motors
- Medical-specific insulation monitor
- Electronics installed in the vehicle
- Microcontroller system
- Power communication system
