MAX800LCPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 842mW |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.75V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX800 |
| Output | Open Drain, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 100μA |
| Max Supply Current | 100μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.55V |
| Max Reset Threshold Voltage | 4.7V |
| Undervoltage Threshold | 4.55V |
| Overvoltage Threshold | 4.7V |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX800LCPE+ Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 16 in total. There is a Tube-packaging method applied to IC management. In this IC power you will find 1 functions for you to refer to. There are 1 channels on this power managment ic that can be found in a series. The purpose of this IC power is to provide you with a reference of 16-DIP (0.300, 7.62mm) functions. There are a lot of similarities between this IC management and other Battery Backup Circuit products. The package peak reflow temperature is specified to be 260. During operation, the power ic is supplied with a voltage of 4.75V. In a 1 supply voltage, the PMIC chip conducts. Power management is included in the Through Hole mount. There is a subcategory called Power Management Circuits for this power management. Power management has a total of 16 pins. 16 pins are present on the power management system. A voltage (Vsup) that doesn't fall below 0V as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. In this case, Through Hole is the recommended mounting type. The temperature of the supervisors should be set to this range: 0°C~70°C TA. While this power management is operating, it will output Open Drain, Push-Pull as the output voltage. In order to maintain a stable supply current for the power management, 100μA is the recommended value. You can always use MAX800, the base supervisor number, to search for similar PMICs of the manufacturer. A power supply of 5V watts is required for the operation of this power management. A maximum supply temperature of 100μA can be used with this power management.
MAX800LCPE+ Features
Battery Backup Circuit type
Minimum supply voltage of 0V
100μA operating supply current
MAX800LCPE+ Applications
There are a lot of Maxim Integrated MAX800LCPE+ Voltage Supervisors applications.
- Electronics installed in the vehicle
- Precision measurement
- Utility meter
- Power distribution systems of infant care room
- Transformer load monitoring equipment
- Computer applications
- Consumer electronics
- Important electronics for automotive protection
- Network equipment
- Detection of phase loss
