MAX802LCPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX802 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 200μA |
| Max Supply Current | 350μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX802LCPA Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 8 in total. Tube-packaging is used. The purpose of this IC management is to provide you with a reference of 1 functions. This power managment ic consists of 1 channels, each of which can be used independently. Please refer to power management for 8-DIP (0.300, 7.62mm) functions. Several of the benefits of this PMIC are also shared by other Battery Backup Circuit products. As specified in the package specification, the peak reflow temperature of the package is set at 245. IC management conducts in a 5V-voltage supply. When 1 is applied to the power ic, it conducts. Power management is included in the Through Hole mount. It is possible to subcategorize this power ic as a Power Management Circuits chip. Power management has a total of 8 pins. The pins of the power management system count 8. It is recommended that Vsup should not be less than 1V for this IC power. It is recommended that the maximum supply voltage (Vsup) in this IC power be no more than 5.5V volts. Mounting type Through Hole is recommended. It is recommended that the supervisor be set to this temperature: 0°C~70°C TA. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. For this power management, there is an 200μA volt supply current. A similar IC managements number of the manufacturer can always be found by using MAX802, the base power ics number. It is necessary to have 5V volts of power in order for this voltage supervisor to operate. The power management can work with a maximum supply temperature of 350μA.
MAX802LCPA Features
Battery Backup Circuit type
Minimum supply voltage of 1V
200μA operating supply current
MAX802LCPA Applications
There are a lot of Maxim Integrated MAX802LCPA Voltage Supervisors applications.
- Insulation fault location system
- Leakage protection
- WiFi router
- Sensitive sensors
- Power communication system
- Medical-specific isolation transformer
- Digitally controlled LDO regulators circuit
- Unattended substation automation
- Military communications
- Microprocessor system
