MAX802TCSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Base Part Number | MAX802 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 50μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 3.075V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.07mA |
| Min Reset Threshold Voltage | 3V |
| Max Reset Threshold Voltage | 3.14V |
| Undervoltage Threshold | 3V |
| Overvoltage Threshold | 3.14V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX802TCSA+ Overview
As you can see, this power management is mounted through 8 terminals. Packaging is in the form of a Tube. There are 1 functions included in this PMIC so that you can refer to them. This power managment ic consists of 1 channels, each of which can be used independently. IC management is packaged as a 8-SOIC (0.154, 3.90mm Width) package. This IC power shares lots of benefits with other Battery Backup Circuit products. Specifies a reflow peak temperature of 260 for the package during reflow. In a 1 supply voltage, the PMIC chip conducts. Surface Mount mounts power management on the wall. There is a subcategory called Power Management Circuits for this power management. In total, the power management has 8 pins in it. There are 8 pins on the power managment ic. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 1V, which is the minimum supply voltage that should be applied. This IC power should be powered by no more than 5.5V volts of supply voltage (Vsup). The recommended mounting type for IC management is Surface Mount. This power management is the recommended temperature range for the supervisors: 0°C~70°C TA. The output voltage of this power managment ic during operation is Push-Pull, Totem Pole. It is estimated that the voltage supervisor's supply current is 50μA. It is always advisable to use MAX802, the base supervisor number, when searching for similar PMICs from the manufacturer. This power management requires 3/5V power to work.
MAX802TCSA+ Features
Battery Backup Circuit type
Minimum supply voltage of 1V
50μA operating supply current
MAX802TCSA+ Applications
There are a lot of Maxim Integrated MAX802TCSA+ Voltage Supervisors applications.
- Multi-voltage system
- Automotive permanent magnet synchronous motors
- Power communication system
- Power distribution systems of CCU
- Military communications
- Detection of phase imbalance
- Magnetic resonance imaging
- FPGA design
- Satellite navigation
- Rechargeable batteries
