MAX806SCPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | MANUAL RESET OPTION |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX806 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 50μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.925V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.07mA |
| Min Reset Threshold Voltage | 2.88V |
| Max Reset Threshold Voltage | 3.02V |
| Undervoltage Threshold | 2.88V |
| Overvoltage Threshold | 3.02V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX806SCPA+ Overview
There are 8 terminals on this power management that allow it to be mounted. There is a Tube-packaging method applied to IC management. As a reference, this IC management includes 1 functions for your convenience. On this supervisor, there is a series of 1 channels that can be found. Please find attached 8-DIP (0.300, 7.62mm) functions for your reference in this IC power. There are a lot of similarities between this IC management and other Battery Backup Circuit products. As specified in the package specification, the peak reflow temperature of the package is set at 260. Power ics operate at 1 supply voltages. Power management is included in the Through Hole mount. This power ic can be sub-categorized as Power Management Circuits. In total, IC powers are 8 pins on the board. Supply voltage (Vsup) should be at least 1V for this power management. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. Power management' mounting is recommended to be done with the Through Hole type of mounting. Temperature setting for the supervisors should be 0°C~70°C TA. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. For this power management, there is an 50μA volt supply current. Additionally, there are many other features that can be found inside of the power management, such as [0]. A similar IC managements number of the manufacturer can always be found by using MAX806, the base power ics number. It is necessary to have 3/5V volts of power in order for this voltage supervisor to operate.
MAX806SCPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 1V
50μA operating supply current
MAX806SCPA+ Applications
There are a lot of Maxim Integrated MAX806SCPA+ Voltage Supervisors applications.
- Detection of phase imbalance
- Electric heating appliances
- Medical-specific isolation transformer
- Data storage applications
- Efficient information transmission
- Electronics installed in the vehicle
- Leakage protection
- Urban rail transit weak current power monitoring
- Personal computers
- Radar
