MAX808MEPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | CMOS RAM WRITE PROTECTION, BATTERY-BACKUP MODE |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX808 |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 48μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.425V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.09mA |
| Min Reset Threshold Voltage | 4.35V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.35V |
| Overvoltage Threshold | 4.5V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX808MEPA+ Overview
As you can see, this power management is mounted through 8 terminals. Packaged in the form of a Tube, power management is easy to use. To assist you, this IC power includes 1 functions. A series of 1 channels can be found on this supervisor. As a reference, this IC power includes 8-DIP (0.300, 7.62mm) functions for your convenience. It is a IC power that shares many benefits with other products from the Battery Backup Circuit line. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. There is a voltage supply of 5V for the PMIC chip, and the chip conducts at that voltage. A supply voltage of 1 is used to conduct the PMIC chip. Through Hole mounts power management on the wall. A IC power such as this can be classified as a Power Management Circuits power management system. Power management has a total of 8 pins. This power management system has 8 pins. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 0V volts. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Mounting type Through Hole is recommended. Temperature setting for the supervisors should be -40°C~85°C TA. As far as the supply current of the power management is concerned, it is 48μA. There are also other features in the software such as [0], just to mention a few. You can always use MAX808, the base supervisor number, to search for similar PMICs of the manufacturer. The voltage supervisor requires a power source of 5V volts in order to work correctly.
MAX808MEPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 0V
48μA operating supply current
MAX808MEPA+ Applications
There are a lot of Maxim Integrated MAX808MEPA+ Voltage Supervisors applications.
- Leakage protection
- Electrical fire monitoring system
- Radar
- Consumer electronics
- Household appliances
- Important electronics for automotive safety
- Detection of phase loss
- Power communication system
- emergency room
- Analog circuit
