MAX809LEUR+T10
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~105°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Base Part Number | MAX809 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 24μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.63V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.06mA |
| Min Reset Threshold Voltage | 4.56V |
| Max Reset Threshold Voltage | 4.7V |
| Threshold Voltage | +4.63V |
| Undervoltage Threshold | 4.56V |
| Overvoltage Threshold | 4.7V |
| Length | 2.92mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX809LEUR+T10 Overview
It is mounted through 3 terminals on the power management. It is packaged with Tape & Reel (TR). The purpose of this IC management is to provide you with a reference of 1 functions. Power management consists of 1 channels, each of which can be used independently. Please refer to power management for TO-236-3, SC-59, SOT-23-3 functions. There are a lot of similarities between this IC management and other Simple Reset/Power-On Reset products. As specified in the package specification, the peak reflow temperature of the package is set at 260. The supervisor is always powered by a 5V volt supply. Power ics operate at 1 supply voltages. The power management is mounted by Surface Mount. As a subcategory, this PMIC chip can be categorized as Power Management Circuits. 3 pins are present in total in this power management. There are 3 pins on the power managment ic. In order for this IC power to function, the supply voltage (Vsup) cannot be less than 1.2V. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Power management recommends the Surface Mount mounting type. The temperature of the supervisors should be set to this range: -40°C~105°C TA. As a result of this supervisor's operation, the output voltage is Push-Pull, Totem Pole. Supplied with a operating current of 24μA, this PMIC is capable of fully function as specified. A similar IC managements number of the manufacturer can always be found by using MAX809, the base power ics number. A power supply of 5V watts is required for the operation of this power management.
MAX809LEUR+T10 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
24μA operating supply current
MAX809LEUR+T10 Applications
There are a lot of Maxim Integrated MAX809LEUR+T10 Voltage Supervisors applications.
- Leakage current detection
- Network equipment
- Telecommunications equipment
- DSP
- Insulation fault location system
- Computer applications
- Utility meter
- WiFi router
- Smart meter
- Medical-specific isolation transformer
