banner_page

MAX810LEUR-T

5V3 Terminals 3-Pin MAX810 Voltage supervisor1 Channels Min 1.2V Max 5.5V


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX810LEUR-T
  • Package: TO-236-3, SC-59, SOT-23-3
  • Datasheet: PDF
  • Stock: 553
  • Description: 5V3 Terminals 3-Pin MAX810 Voltage supervisor1 Channels Min 1.2V Max 5.5V (Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case TO-236-3, SC-59, SOT-23-3
Number of Pins 3
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2010
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 3
ECCN Code EAR99
Type Simple Reset/Power-On Reset
Terminal Finish Tin/Lead (Sn/Pb)
Subcategory Power Management Circuits
Max Power Dissipation 320mW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 240
Number of Functions 1
Supply Voltage 5V
Terminal Pitch 0.95mm
Time@Peak Reflow Temperature-Max (s) 20
Base Part Number MAX810
Output Push-Pull, Totem Pole
Pin Count 3
Power Supplies 5V
Number of Channels 1
Voltage 5V
Max Supply Voltage 5.5V
Min Supply Voltage 1.2V
Operating Supply Current 24μA
Nominal Supply Current 24μA
Adjustable Threshold NO
Watchdog Timer No
Reset Active High
Voltage - Threshold 4.63V
Number of Voltages Monitored 1
Reset Timeout 140ms Minimum
Supply Current-Max (Isup) 0.06mA
Min Reset Threshold Voltage 4.56V
Max Reset Threshold Voltage 4.7V
Threshold Voltage +4.63V
Undervoltage Threshold 4.56V
Overvoltage Threshold 4.7V
Height 1.02mm
Length 3.04mm
Width 1.4mm
REACH SVHC Unknown
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead

MAX810LEUR-T Overview


A total of 3 terminals are used to mount this power management. In terms of packaging, power management follows the Tape & Reel (TR) model. Please find attached 1 functions for your reference in this IC power. This power management is made up of 1 channels which are available in a series format. IC management is packaged as a TO-236-3, SC-59, SOT-23-3 package. With power management, you get a lot of benefits that you won't find in other Simple Reset/Power-On Reset products. During the reflow process, a peak temperature of 240 is specified for the package. IC management conducts at a voltage of 5V. Power ics operate at 1 supply voltages. By Surface Mount, IC management has been mounted. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. In total, IC powers are 3 pins on the board. There are 3 pins on the power managment ic. In order for this PMIC to work correctly, the minimum supply voltage (Vsup) should be greater than 1.2V. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. The recommended mounting type for IC management is Surface Mount. The supervisors should be set to the following temperature: -40°C~85°C TA. During operation, this power management system outputs Push-Pull, Totem Pole. In order to maintain a stable supply current for the power management, 24μA is the recommended value. It is always advisable to use MAX810, the base supervisor number, when searching for similar PMICs from the manufacturer. The voltage supervisor requires a power source of 5V volts in order to work correctly.

MAX810LEUR-T Features


Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
24μA operating supply current

MAX810LEUR-T Applications


There are a lot of Maxim Integrated MAX810LEUR-T Voltage Supervisors applications.

  • Sensitive sensors
  • Medical-specific insulation monitor
  • Stable power system
  • Power distribution systems of CCU
  • Insulation fault location system
  • Consumer electronics
  • Low voltage/high power - AI, GPU
  • Electronics installed in the vehicle
  • Rechargeable batteries
  • Medical-specific isolation transformer

Write a review

Note: HTML is not translated!
    Bad           Good