MAX810MTRG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 23 hours ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~105°C TJ |
| Packaging | Cut Tape (CT) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin (Sn) |
| Subcategory | Power Management Circuits |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MAX810 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 800nA |
| Nominal Supply Current | 2.5μA |
| Adjustable Threshold | NO |
| Reset | Active High |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Halogen Free | Halogen Free |
| Supply Current-Max (Isup) | 0.0025mA |
| Min Reset Threshold Voltage | 4.31V |
| Max Reset Threshold Voltage | 4.45V |
| Threshold Voltage | +4.38V |
| Undervoltage Threshold | 4.38V |
| Overvoltage Threshold | 4.45V |
| Height | 1.016mm |
| Length | 3.0226mm |
| Width | 1.397mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX810MTRG Overview
There are 3 terminals connected to this power management, which makes it easy to mount. Packaged in a Cut Tape (CT)-shape, IC management comes with a number of features. Power management is possible to find a series of 1 functions. Power management consists of 1 channels, each of which can be used independently. In this IC management you will find TO-236-3, SC-59, SOT-23-3 functions for you to refer to. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. Specifies a reflow peak temperature of 260 for the package during reflow. When 3.3V is applied to the power ic, it conducts. A supply voltage of 1 is used to conduct the PMIC chip. Power management is included in the Surface Mount mount. The power management system can be categorized as a Power Management Circuits chip. It has a total of 3 pins that are attached to IC management. 3 pins make up the power management. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1.2V. There should be no more than 5.5V volts of supply voltage (Vsup) in this power management. In this case, Surface Mount is the recommended mounting type. It is recommended to set the supervisor's temperature to this range: -40°C~105°C TJ. Power management has an output of Push-Pull, Totem Pole during operation. It is estimated that the voltage supervisor's supply current is 800nA. It is always advisable to use MAX810, the base supervisor number, when searching for similar PMICs from the manufacturer.
MAX810MTRG Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
800nA operating supply current
MAX810MTRG Applications
There are a lot of ON Semiconductor MAX810MTRG Voltage Supervisors applications.
- Important electronics for automotive protection
- Electric heating appliances
- Dash board
- Power distribution systems of operating room
- Embedded computing
- Microcontroller system
- Automotive power systems
- Functional modules
- External alarm
- Transformer load monitoring equipment
