MAX814LCPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.75V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX814 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 75μA |
| Max Supply Current | 75μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.7V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.65V |
| Max Reset Threshold Voltage | 4.75V |
| Threshold Voltage | +4.7V |
| Undervoltage Threshold | 4.65V |
| Overvoltage Threshold | 4.75V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX814LCPA+ Overview
A total of 8 terminals are used to mount this power management. This power ic is packaged in a way that looks like a Tube. There are 1 functions included in this PMIC so that you can refer to them. This power managment ic consists of 1 channels, each of which can be used independently. IC management is packaged as a 8-DIP (0.300, 7.62mm) package. It is a IC power that shares many benefits with other products from the Simple Reset/Power-On Reset line. During the reflow process, a peak temperature of 260 is specified for the package. In a 4.75V supply voltage, the power management conducts. Power management conducts at a voltage of 1. Using Through Hole, IC management is mounted. There is a subcategory called Power Management Circuits for this power management. A total of 8 pins are located on this power management. There are 8 pins on the supervisor. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1V volts. There should be no more than 5.5V volts of supply voltage (Vsup) in this power management. Power management' mounting is recommended to be done with the Through Hole type of mounting. It is recommended that the supervisor be set to this temperature: 0°C~70°C TA. As a result of this supervisor's operation, the output voltage is Push-Pull, Push-Pull. As far as the supply current of the power management is concerned, it is 75μA. A similar IC managements number of the manufacturer can always be found by using MAX814, the base power ics number. At most, voltage supervisor can operate at a supply temperature of 75μA.
MAX814LCPA+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
75μA operating supply current
MAX814LCPA+ Applications
There are a lot of Maxim Integrated MAX814LCPA+ Voltage Supervisors applications.
- Leakage protection
- Power distribution systems of operating room
- Data storage applications
- Solar power charger
- Sensitive sensors
- Smart meter
- Network equipment
- Microprocessor system
- Rechargeable batteries
- Unattended substation automation
