MAX814LEPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.75V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX814 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 85μA |
| Max Supply Current | 85μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.7V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.65V |
| Max Reset Threshold Voltage | 4.75V |
| Threshold Voltage | +4.7V |
| Undervoltage Threshold | 4.65V |
| Overvoltage Threshold | 4.75V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX814LEPA+ Overview
There are 8 mounting terminals on the voltage supervisor, each of which has a different function. Tube-packaging is used. In this PMIC, you can find 1 functions for your reference. Power management consists of 1 channels, each of which can be used independently. As a reference, this IC power includes 8-DIP (0.300, 7.62mm) functions for your convenience. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. The supervisor is always powered by a 4.75V volt supply. IC management conducts in a 1-voltage supply. The mount is attached to Through Hole. There is a subcategory of this power ic known as Power Management Circuits. The total number of pins on this power management is 8. 8 pins are present on the power management system. Supply voltage (Vsup) should be at least 1.2V for this power management. This IC power should be powered by no more than 5.5V volts of supply voltage (Vsup). Power management recommends the Through Hole mounting type. It is recommended to set the supervisor's temperature to this range: -40°C~85°C TA. During normal operation, this power managment ic can generate Push-Pull, Push-Pull of output voltage. The power management's supply current is 85μA. You can always use MAX814, the base supervisor number, to search for similar PMICs of the manufacturer. A maximum supply temperature of 85μA can be used with this power management.
MAX814LEPA+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
85μA operating supply current
MAX814LEPA+ Applications
There are a lot of Maxim Integrated MAX814LEPA+ Voltage Supervisors applications.
- Radio
- Automotive permanent magnet synchronous motors
- Microcontroller system
- Power distribution systems of CCU
- Efficient information transmission
- Kitchen appliances
- Automotive power systems
- Important electronics for automotive protection
- Medical-specific insulation monitor
- Military electronics
