MAX814TCPA+
| Parameters | |
|---|---|
| Min Reset Threshold Voltage | 3V |
| Max Reset Threshold Voltage | 3.06V |
| Threshold Voltage | +3.03V |
| Undervoltage Threshold | 3V |
| Overvoltage Threshold | 3.06V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.07V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX814 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 75μA |
| Max Supply Current | 75μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active High/Active Low |
| Voltage - Threshold | 3.03V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
MAX814TCPA+ Overview
Power management is mounted through 8 terminals. It is packaged with Tube. In this IC power you will find 1 functions for you to refer to. A series of 1 channels can be found on this supervisor. To assist you, this PMIC includes 8-DIP (0.300, 7.62mm) functions. Several of the benefits of this PMIC are also shared by other Simple Reset/Power-On Reset products. IC management is specified that the package peak reflow temperature should be 260. Manage ics operate at 3.07V supply voltages. IC management is possible to find a succession of 1 voltages that have been checked. Using Through Hole, IC management is mounted. The power management system can be categorized as a Power Management Circuits chip. A total of 8 pins are located on this power management. 8 pins make up the power management. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1V volts. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Power management recommends the Through Hole mounting type. This range of temperature should be set for the supervisors: 0°C~70°C TA. While in operation, this supervisor has a voltage output of Push-Pull, Push-Pull. It is estimated that the voltage supervisor's supply current is 75μA. To find similar IC managements from the manufacturer, you can always search by MAX814. At most, voltage supervisor can operate at a supply temperature of 75μA.
MAX814TCPA+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
75μA operating supply current
MAX814TCPA+ Applications
There are a lot of Maxim Integrated MAX814TCPA+ Voltage Supervisors applications.
- Electronics installed in the vehicle
- Power distribution systems of infant care room
- Battery cars
- Low voltage/high power - AI, GPU
- Electrical fire monitoring system
- Utility meter
- Fire equipment power monitoring system
- DSP
- Display equipment
- Data storage applications
