Parameters |
Number of Pins |
8 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2006 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Type |
Battery Backup Circuit |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Power Management Circuits |
Max Power Dissipation |
471mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
245 |
Number of Functions |
1 |
Supply Voltage |
4.75V |
Base Part Number |
MAX817 |
Output |
Push-Pull, Totem Pole |
Pin Count |
8 |
Power Supplies |
5V |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
0V |
Operating Supply Current |
11μA |
Adjustable Threshold |
NO |
Watchdog Timer |
Yes |
Reset |
Active Low |
Voltage - Threshold |
4.65V |
Number of Voltages Monitored |
1 |
Reset Timeout |
140ms Minimum |
Supply Current-Max (Isup) |
0.045mA |
Min Reset Threshold Voltage |
4.5V |
Max Reset Threshold Voltage |
4.75V |
Undervoltage Threshold |
4.5V |
Overvoltage Threshold |
4.75V |
Length |
4.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
MAX817LCSA Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 8 in total. Tube-packaging is used. Please refer to this PMIC for 1 functions. On this supervisor, there is a series of 1 channels that can be found. In this PMIC, you can find 8-SOIC (0.154, 3.90mm Width) functions for your reference. There are a lot of similarities between this IC management and other Battery Backup Circuit products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 245. IC management conducts at a voltage of 4.75V. In a 1 supply voltage, the PMIC chip conducts. The mount is provided by Surface Mount. The power management system can be categorized as a Power Management Circuits chip. In total, it has 8 pins on IC management. Power managment ic pin count is 8. It is recommended that Vsup should not be less than 0V for this IC power. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. In this case, Surface Mount is the recommended mounting type. We recommend setting the supervisors to 0°C~70°C TA degrees. During normal operation, this power managment ic can generate Push-Pull, Totem Pole of output voltage. For this power management, there is an 11μA volt supply current. A similar IC managements number of the manufacturer can always be found by using MAX817, the base power ics number. To be able to work, this power management requires 5V volts of power.
MAX817LCSA Features
Battery Backup Circuit type
Minimum supply voltage of 0V
11μA operating supply current
MAX817LCSA Applications
There are a lot of Maxim Integrated MAX817LCSA Voltage Supervisors applications.
- Radio
- Utility meter
- Unattended substation automation
- Detection of phase imbalance
- Power distribution systems of operating room
- Battery cars
- DSP
- Functional modules
- Electronics installed in the vehicle
- Insulation fault location system