MAX817LEPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.75V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX817 |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 11μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.06mA |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX817LEPA+ Overview
This voltage supervisor has a total of 8 mounting terminals that can be used for mounting. Packaged in the form of a Tube, power management is easy to use. As a reference, this IC management includes 1 functions for your convenience. Depending on the power managment ic you are looking at, you can find a total of 1 channels. To assist you, this PMIC includes 8-DIP (0.300, 7.62mm) functions. There are a lot of similarities between this IC management and other Battery Backup Circuit products. Specifies a reflow peak temperature of 260 for the package during reflow. During operation, the power ic is supplied with a voltage of 4.75V. There is a voltage supply of 1 for the PMIC chip, and the chip conducts at that voltage. The mount is attached to Through Hole. This power ic can be sub-categorized as Power Management Circuits. Power management has a total of 8 pins. Pin count of the power management is 8. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 0V volts. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. The recommended mounting type for IC management is Through Hole. The supervisors should be set to the following temperature: -40°C~85°C TA. The power management's supply current is 11μA. You can always use MAX817, the base supervisor number, to search for similar PMICs of the manufacturer. A power supply of 5V watts is required for the operation of this power management.
MAX817LEPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 0V
11μA operating supply current
MAX817LEPA+ Applications
There are a lot of Maxim Integrated MAX817LEPA+ Voltage Supervisors applications.
- Leakage current detection
- Magnetic resonance imaging
- FPGA design
- Medical-specific insulation monitor
- Detection of phase loss
- Detection of phase imbalance
- Fire equipment power monitoring system
- Power distribution systems of operating room
- DSP
- Network equipment
