MAX817MCPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX817 |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 11μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.4V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.045mA |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX817MCPA+ Overview
Power management is mounted through 8 terminals. This power ic is packaged in a way that looks like a Tube. In this IC power you will find 1 functions for you to refer to. It is possible to find on this power management a series of 1 channels. The purpose of this IC power is to provide you with a reference of 8-DIP (0.300, 7.62mm) functions. There are a number of benefits that this PMIC has in common with other Battery Backup Circuit manage ics. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. The supervisor is always powered by a 4.5V volt supply. In a 1 supply voltage, the PMIC chip conducts. Through Hole mounts power management on the wall. The power management system can be categorized as a Power Management Circuits chip. In total, the power management has 8 pins in it. The pins of the power management system count 8. A voltage (Vsup) that doesn't fall below 0V as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.5V volts. In this case, Through Hole is the recommended mounting type. We recommend setting the supervisors to 0°C~70°C TA degrees. It is estimated that the voltage supervisor's supply current is 11μA. To find similar IC managements from the manufacturer, you can always search by MAX817. To operate this power management, you will need at least 5V volts of power.
MAX817MCPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 0V
11μA operating supply current
MAX817MCPA+ Applications
There are a lot of Maxim Integrated MAX817MCPA+ Voltage Supervisors applications.
- Leakage current detection
- Automotive power systems
- Military electronics
- Refrigeration
- Insulation fault location system
- WiFi router
- Medical-specific insulation monitor
- Household appliances
- Military communications
- DC stabilized power supply module
