MAX818LCSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.75V |
| Base Part Number | MAX818 |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 45μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.045mA |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX818LCSA+ Overview
Power management is mounted through 8 terminals. In terms of packaging, power management follows the Tube model. There are 1 functions included in this PMIC so that you can refer to them. This power managment ic consists of 1 channels, each of which can be used independently. Please refer to power management for 8-SOIC (0.154, 3.90mm Width) functions. This IC power shares lots of benefits with other Battery Backup Circuit products. As specified in the package specification, the peak reflow temperature of the package is set at 260. The supervisor is always powered by a 4.75V volt supply. When 1 is applied to the power ic, it conducts. Surface Mount is the one that mounts power management. There is a subcategory called Power Management Circuits for this power management. Power management has a total of 8 pins. Power managment ic pin count is 8. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 0V. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Power management' mounting is recommended to be done with the Surface Mount type of mounting. The supervisors should be set to the following temperature: 0°C~70°C TA. The power management's supply current is 45μA. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX818, which is the base power ics number. There is a requirement for 5V power to power this power management.
MAX818LCSA+ Features
Battery Backup Circuit type
Minimum supply voltage of 0V
45μA operating supply current
MAX818LCSA+ Applications
There are a lot of Maxim Integrated MAX818LCSA+ Voltage Supervisors applications.
- Set top box
- Functional modules
- Satellite navigation
- Important electronics for automotive protection
- Low voltage/high power - AI, GPU
- Electric heating appliances
- Leakage current detection
- Analog circuit
- Sensitive sensors
- Stable power system
