MAX818MCPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX818 |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 11μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.4V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.045mA |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX818MCPA+ Overview
There are 8 terminals connected to this power management, which makes it easy to mount. It is packaged with Tube. Please refer to this PMIC for 1 functions. On this supervisor, there is a series of 1 channels that can be found. The purpose of this IC power is to provide you with a reference of 8-DIP (0.300, 7.62mm) functions. There are a number of benefits that this PMIC has in common with other Battery Backup Circuit manage ics. Specifies a reflow peak temperature of 260 for the package during reflow. A supply voltage of 4.5V is used to conduct the PMIC chip. Power management conducts at a voltage of 1. By Through Hole, IC management has been mounted. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. Taking into account all of the pins, this power management has a total of 8. There are 8 pins on the supervisor. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 0V, which is the minimum supply voltage that should be applied. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. Mounting type Through Hole is recommended. The temperature of the supervisors should be set to this range: 0°C~70°C TA. Supplied with a operating current of 11μA, this PMIC is capable of fully function as specified. For similar manage ics search of the manufacturer, you can always refer to MAX818, the base PMIC number. To operate this power management, you will need at least 5V volts of power.
MAX818MCPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 0V
11μA operating supply current
MAX818MCPA+ Applications
There are a lot of Maxim Integrated MAX818MCPA+ Voltage Supervisors applications.
- emergency room
- Microcontroller system
- Leakage current detection
- Consumer electronics
- WiFi router
- Microprocessor system
- Detection of phase sequence
- Military electronics
- DC stabilized power supply module
- Efficient information transmission
