MAX820MCSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX820 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.75V |
| Operating Supply Current | 150μA |
| Max Supply Current | 150μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.37V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX820MCSE+ Overview
As you can see, this power management is mounted through 16 terminals. There is a Tube-packaging method applied to IC management. There are 1 functions included in this PMIC so that you can refer to them. On this supervisor, there is a series of 1 channels that can be found. In this IC management you will find 16-SOIC (0.154, 3.90mm Width) functions for you to refer to. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. There is a specification for the peak reflow temperature of the package to be 260. The supervisor is always powered by a 5V volt supply. There is a voltage supply of 1 for the PMIC chip, and the chip conducts at that voltage. The power management is mounted by a Surface Mount-axis. There is a subcategory of this power ic known as Power Management Circuits. In total, it has 16 pins on IC management. 16 pins are on the supervisor. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 2.75V. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. Surface Mount mounting is recommended. It is recommended that the supervisor be set to this temperature: 0°C~70°C TA. During normal operation, this power managment ic can generate Push-Pull, Push-Pull of output voltage. There is a 150μA supply current present in the power management. It is always advisable to use MAX820, the base supervisor number, when searching for similar PMICs from the manufacturer. This power management requires 3/5V power to work. At the most, voltage supervisor can work with a supply temperature of 150μA.
MAX820MCSE+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 2.75V
150μA operating supply current
MAX820MCSE+ Applications
There are a lot of Maxim Integrated MAX820MCSE+ Voltage Supervisors applications.
- External alarm
- Network equipment
- Detection of phase imbalance
- Dash board
- Smart meter
- Automotive permanent magnet synchronous motors
- Telecommunications equipment
- DVR
- Rechargeable batteries
- Military communications
