MAX8212CSA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX8212 |
| Output | Open Drain or Open Collector |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 15μA |
| Max Supply Current | 15μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | Adjustable/Selectable |
| Number of Voltages Monitored | 1 |
| Reset Timeout | <1ms Minimum |
| Min Reset Threshold Voltage | 1.11V |
| Max Reset Threshold Voltage | 1.19V |
| Undervoltage Threshold | 1.11V |
| Overvoltage Threshold | 1.19V |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX8212CSA+T Overview
There are 8 mounting terminals on the voltage supervisor, each of which has a different function. Power management is packaged in a Tape & Reel (TR) way. In this IC power you will find 1 functions for you to refer to. Power management consists of 1 channels, each of which can be used independently. The purpose of this IC power is to provide you with a reference of 8-SOIC (0.154, 3.90mm Width) functions. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. Specifies a reflow peak temperature of 260 for the package during reflow. The supervisor is always powered by a 5V volt supply. When 1 is applied to the power ic, it conducts. The mount is provided by Surface Mount. This power ic can be sub-categorized as Power Management Circuits. 8 pins are present in total in this power management. 8 pins make up the power management. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 2V. The supply voltage (Vsup) should not exceed 16.5V volts in this IC power. The recommended mounting type for IC management is Surface Mount. It is recommended to set the supervisor's temperature to this range: 0°C~70°C TA. Power management has an output of Open Drain or Open Collector during operation. In order to maintain a stable supply current for the power management, 15μA is the recommended value. For similar manage ics search of the manufacturer, you can always refer to MAX8212, the base PMIC number. There is a requirement for 5V power to power this power management. The power management can work with a maximum supply temperature of 15μA.
MAX8212CSA+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 2V
15μA operating supply current
MAX8212CSA+T Applications
There are a lot of Maxim Integrated MAX8212CSA+T Voltage Supervisors applications.
- Battery-powered equipment
- Detection of phase loss
- Telecommunications equipment
- Dash board
- FPGA design
- Electric heating appliances
- Stable power system
- Power distribution systems of operating room
- WiFi router
- Insulation fault location system
