MAX824MEUK+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 571mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX824 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 5 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 10μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.38V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.024mA |
| Min Reset Threshold Voltage | 4.31V |
| Max Reset Threshold Voltage | 4.45V |
| Undervoltage Threshold | 4.31V |
| Overvoltage Threshold | 4.45V |
| Height | 1.3mm |
| Length | 3mm |
| Width | 1.75mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX824MEUK+T Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 5 in total. Packaging is in the form of a Tape & Reel (TR). Please find attached 1 functions for your reference in this IC power. This power management is made up of 1 channels which are available in a series format. To assist you, this PMIC includes SC-74A, SOT-753 functions. As with other Simple Reset/Power-On Reset products, this IC management also offers a wide range of benefits. Specifies a reflow peak temperature of 260 for the package during reflow. A supply voltage of 5V is used to conduct the PMIC chip. When a supply voltage of 1 is applied to the power ic, it conducts. Surface Mount is the one that mounts power management. A IC power such as this can be classified as a Power Management Circuits power management system. In total, IC powers are 5 pins on the board. Power managment ic pin count is 5. There should be a minimum voltage supply (Vsup) of 1.2V for this PMIC. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. Surface Mount mounting is recommended. The temperature of the supervisors should be set to this range: -40°C~125°C TA. Power management has an output of Push-Pull, Totem Pole during operation. Supplied with a operating current of 10μA, this PMIC is capable of fully function as specified. It is always advisable to use MAX824, the base supervisor number, when searching for similar PMICs from the manufacturer. To be able to work, this power management requires 5V volts of power.
MAX824MEUK+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
10μA operating supply current
MAX824MEUK+T Applications
There are a lot of Maxim Integrated MAX824MEUK+T Voltage Supervisors applications.
- Low voltage/high power - AI, GPU
- Detection of phase sequence
- Automotive permanent magnet synchronous motors
- Leakage protection
- Computer applications
- Power communication system
- Rechargeable batteries
- Detection of phase imbalance
- Medical-specific insulation monitor
- Precision measurement
